How to Install Blinds: Identify the Mount and Secure the Headrail
Every blind goes up the same way in outline: prepare, fix the brackets, lock in the headrail. The details differ by system, so identify yours first and follow its own instructions.
By DecoraMintPublished 6-minute readMore in Blinds & Shades

In this guide
Most blind installs go wrong at the first screw, not the last. Brackets set a hair out of level, or a front edge a little behind its partner, and the headrail either refuses to seat or hangs with a bottom rail that slopes. The rest of the job is clipping things together. Put the time into the brackets and the rest follows.
The steps below follow a maker’s printed manual, LEVOLOR’s installation instructions for its cordless wood blinds, because the pattern (two end brackets, extra supports for wide blinds, a headrail that tilts in) is the one most horizontal blinds share. Blinds.com’s horizontal install page describes the same sequence. The measurements are LEVOLOR’s for that line; roller shades, cellular shades and vertical blinds have their own hardware, so use the booklet in your box for the exact screw lengths and spacers.
What to have on the sill
LEVOLOR lists a pencil, a level (it recommends a laser level), a tape measure, a drill with a 3/32 inch bit, and a 1/4 inch hex driver and flat-blade screwdriver. Home Depot’s blind installation guide adds a stepladder to the list. The screws in the box suit wood. Drywall needs anchors, which the Home Depot guide recommends for outside mounts unless you are screwing into wood.
Leave any slat protector tape on until the blind is up, and take out a shipping piece from inside the headrail if there is one, as LEVOLOR directs.
Before the drill comes out
Set up the stepladder square to the window and keep your belt buckle between the side rails. The Nevada Division of Industrial Relations’ ladder safety bulletin calls for three points of contact on the way up and while working, and warns against overreaching: climb down and move the ladder instead. A wide blind is a two-person lift.
Then think about what is behind the surface. Outside mounts often land in the wall above a window, where wires can run to a nearby switch or outlet. Klein’s stud finder manual warns that a stud finder can mistake wiring or pipes for studs and advises turning off power before drilling into a wall. If you cannot rule out a cable at a bracket position, turn off the circuit at the breaker or move the bracket.
Inside mount
An inside mount puts the blind within the frame, so the brackets attach to the head or sides of the opening.
- Hold the blind up and mark the headrail ends with a pencil, using the level. Blinds.com’s page uses the same pencil marks at each end, and has the bracket doors face into the room.
- Choose the screw pattern. LEVOLOR allows one side screw and one top screw per end bracket, two diagonal side screws, or two top screws. For a ceiling mount it uses top screws, or one top and one rear screw when the bracket sits flush with the back wall.
- Keep the front edges of the two end brackets aligned. LEVOLOR marks this as important. Mark each hole, drill with the 3/32 inch bit, and drive the screws it supplies (two 1 1/2 inch screws per bracket).
- Keep the slats off the glass. For its 2 1/2 inch slats, LEVOLOR uses spacer blocks to hold the end brackets at least 3/8 inch away from the glass, so tilted slats do not rub. Spacer blocks take longer screws than the ones in the bag.
- Check the bracket faces. They should sit flat against the frame. LEVOLOR provides shims to level the blind on an uneven surface, and the shims can be cut thinner along their fold line.
- Add the center support if the blind needs one. LEVOLOR’s chart: none up to 48 inches wide, one from 48 1/8 to 60 inches, two from 60 1/8 to 96 inches. Space them evenly between the ends, shifting a bracket if it would collide with a mechanism inside the headrail. The rear of all brackets must align for an inside mount.
Outside mount
Here the blind hangs on the wall or trim above the opening. LEVOLOR needs a flat vertical surface of at least 1 3/4 inches for the end brackets, so check the trim above the window before you commit to it, and never mount a bracket on curved molding.
Center the headrail over the opening at the height you want and mark each end lightly. Make a second mark 1/4 inch beyond each end mark: the outer edge of each end bracket goes there. Mark diagonal screw holes, drill, and fasten with two screws per bracket. Keep the tops of the brackets level and aligned. Spacer blocks are required with 2 1/2 inch slats on an outside mount and optional with 2 inch slats, and LEVOLOR recommends a 2 1/2 inch screw to go through them. LEVOLOR also offers 2 inch and 4 inch extension brackets that go in place of the spacer blocks.
Hang the headrail
If the blind has magnetic valance clips, fit them to the valance first. LEVOLOR sets them 5 1/2 inches in from each end of a valance narrower than 36 inches, and 10 inches in on wider ones, with any extra clips evenly spaced between.
Tilt the headrail so its back lip slides under the front lips of the brackets, then push it back against the end brackets and check that any center bracket’s front lip is under the headrail’s front lip. If the rail rattles in the end brackets, bend the bracket tabs outward; if it fights you, bend them inward. Press each end cover down until it snaps over the locking tab. Attach the wand, then the valance, and, if you ordered them, hold-down brackets: lower the blind fully, line the brackets up with the pins in the bottom rail ends, and fasten them to the jamb, sill or wall. Release cords only after the headrail is in place, as Blinds.com advises.
If the blind will not seat, LEVOLOR’s troubleshooting is to check that the brackets are level and aligned, that screw heads sit flush, and that the headrail is fully inserted. If the slat pack looks pushed toward one side, slide the headrail the opposite way in the end brackets and adjust the tabs to hold it.
How it should look once it is up
Brackets decide more of the look than people expect. An inside mount with the blind raised leaves a stack of slats at the top of the glass, so a window with a handsome painted frame keeps its trim and the blind reads as part of the sash. Wood-toned slats against white casing give a clean, graphic outline when tilted open at a slant.
Outside mounts suit a window that is short, crooked or plain. Hung above the trim and wide enough to cover the casing, the blind turns the opening into one tidy rectangle and stacks up on the wall instead of in front of the glass.
Cords and safety devices
Fit every retaining and safety part supplied before anyone uses the blind. The Consumer Product Safety Commission calls cordless coverings the safest choice where young children are present. For blinds that keep cords, it says cord stops should sit within 1 to 2 inches of the headrail when the blind is fully lowered, and that continuous-loop cords should be anchored to the wall or floor, taut but operable. It also says most blinds sold before November 2000 have inner cords a child can pull into a loop, and that they should be replaced immediately. Cribs, beds and furniture belong away from window cords. CPSC points to the Window Covering Safety Council for free cord-stop and hold-down kits.
For a motorized blind, follow the maker’s power instructions; fixed wiring is a job for an electrician.
Last, run the blind up and down from its normal position. If a bracket shifts or the rail binds, stop and fix the bracket rather than forcing the mechanism.


