Skip to content
DecoraMint

How to Measure for Curtains (Length, Width and Rod Placement)

How to measure for curtains: place the rod first, then size panel width for fullness and length for a sill, float, break or puddle finish. Worked example.

By DecoraMintPublished 4-minute readMore in Blinds & Shades

White curtains hanging beside two windows overlooking trees
In this guide
  1. Step 1: choose the hem
  2. Step 2: mark the hardware
  3. Step 3: width
  4. Step 4: length
  5. Step 5: match a stock size or alter
  6. Two windows that look the same

Decide where the hem will land before you pick up a tape measure. That single choice, a hover just off the floor or a deliberate puddle or a stop at the sill, sets the length, and the length tells you where the rod has to go. Width comes last, because it depends on the fabric’s fullness and on how the maker counts it. Work in that order and each measurement feeds the next.

Step 1: choose the hem

Sill-length curtains suit windows with a radiator or a desk beneath them. Floor-length ones are the usual choice in living rooms and bedrooms. Within floor-length, there are three looks:

  • A hover keeps the hem clear of the floor, so it does not drag or collect dust. The Shade Store’s grommet measuring sheet recommends ordering about half an inch off the floor for drapery that opens and closes often.
  • A break lets the fabric just touch the floor, which looks softer and hides an uneven floor.
  • A puddle puts extra fabric on the floor on purpose. The same sheet suggests a small puddle of 1 to 6 inches, and other guides go larger, so look at photos of the amount you have in mind before adding it.

Stand where a curtain would hang, check the clearance around furniture, opening windows and heating equipment, and keep fabric away from radiators and baseboard heaters. Pick the look and turn it into a number to add to or subtract from the floor measurement.

Step 2: mark the hardware

Put painter’s tape where the rod will sit, brackets and finials included. A rod’s advertised length rarely includes finials, and a center support will interrupt where panels can slide, so draw the outline the hardware will really occupy. For the side-to-side position, The Shade Store suggests extending out from the frame as much as 6 to 12 inches on each side, which makes the window look larger and keeps the glass clear when the curtains are open.

If the curtains need to open and close, the hardware span is the width you will be covering. If they are fixed decorative panels, the span can be a little narrower.

Step 3: width

Measure the hardware span between the bracket ends, then find out how your seller counts width. There are three conventions, and mixing them up produces curtains that are half as full as you expected, or twice as wide.

  • Ready-made panels list the flat, ungathered width of a single panel. You multiply the span by the fullness you want and divide by the panel width. Guides vary, and Screwfix, for example, gives a range of 1.5 to 2.5 times the track or pole width.
  • Ready-made pairs may list the combined width, so do not double a number that already counts both panels.
  • Custom orders often ask for the coverage width, with the fullness already built in. The Shade Store’s grommet sheet says its ordering width includes about 1.8 times fullness (its pinch-pleat sheet builds in roughly 2.5 times, so the figure follows the heading), and that a pair’s total is divided into two equal panels.

Here is the arithmetic on a hardware span of 64 inches with a target of twice that width, or 128 inches of flat fabric. Two 64-inch panels give exactly that. Two 50-inch panels give 100 inches, about 1.56 times the span, which will look flat and thin. Four 50-inch panels give 200 inches, about 3.1 times, which is very full. Pick the panel width and count that suit the heading and the look you want.

Step 4: length

Measure from the point where the fabric will actually hang, not from the top of the glass. That reference depends on the heading:

  • Rings and clips hang the fabric below the rod, so measure from the bottom of the ring.
  • Rod pocket and tab styles begin at or just under the rod.
  • Grommets put the fabric top above the opening. The Shade Store notes the drapery top sits about an inch higher than the top of the grommet opening, and its sheet lists a hardware allowance, for instance adding an inch from the top of a pole to the top of the fabric.

Measure from that reference down to the hem you chose in step 1, and do it at the left, center and right, because floors and ceilings are rarely level. Then take the number and adjust for the hover, break or puddle.

Step 5: match a stock size or alter

Ready-made curtains come in set lengths. Pottery Barn’s curtain guide lists 84, 96, 108 and 120 inches, but that is one retailer’s range, and not every fabric comes in all four. Treat a stock length as a starting point; your hem line decides the final length. If your measurement falls between sizes, you can buy the longer one and hem it, order custom, or move the rod. Check how the curtain’s lining, border or weighted hem affects alteration, since each shortens differently. A short panel cannot be fixed afterward, so round up. The window treatments category has curtains in a range of lengths if you need to compare.

Two windows that look the same

They often are not, so run the whole sequence for each one: heading, hardware span, width convention and panel count, drop at three points, hem and alteration plan.

All guides